SKS-FILES FORUM

SKS Carbines => Unaltered SKS Rifles => General SKS Discussion => Topic started by: Bacarnal on May 26, 2020, 08:47:08 PM

Title: SKS Cleaning Kit Use
Post by: Bacarnal on May 26, 2020, 08:47:08 PM
    Having read a post about someone having difficulties cleaning the bore with the SKS cleaning rod being too short, it piqued my curiosity.  I had seen the Russian SKS posters on the forum earlier depicting how to correctly assemble the cleaning gear, I thought I'd give it a try.  Pictures below.

1.  I found that you had to assemble the case/detent pin AND the cap onto the cleaning rod BEFORE putting on either the brush or the patch jag.
2.  After inserting the cleaning tool into the bore, you lock the cap over the back of the sight/cleaning rod holder.
3.  The cleaning tool JUST comes to the end of the rifling, as seen by the end of the patch.  The patch stays on the jag and can be constantly used.
4.  Running the cleaning rod back and forth with the desired cleaning tool attached, the rod is held captive in the bore by the cap until the cap is unlocked to either use a different tool or finish.

    Having seen the directions on the poster, I found that it wasn't too complicated for even this old Jarhead, though without the pix, it might have been a tad difficult.  No crayons chuckles1.  This method has the plus of ensuring the crown isn't damaged.  The down side is that the cleaning rod IS too short to be used the way MOST of us were taught in the Military, that is to clean from the chamber end so as to not touch the crown.  Weapons like the Garand, M1 Carbine or M14 have to be cleaned from the muzzle end and some newer military rod kits come with a plastic rod guide to protect the crown, but they are a pain to use since they aren't captive.
    I did find out that the standard USGI .30 cleaning rod has a VERY close thread pitch to the SKS cleaning rod and that you can use it as an extension.  I hope this has been informative.
    If this subject has been covered before, please excuse me since I didn't find it.  Cheers, Bruce.


(https://i.ibb.co/ZS0P0Y6/15905372156815613582730033890639.jpg) (https://ibb.co/gdxpxPM)

(https://i.ibb.co/8g2QH36/15905372607007678501381973153421.jpg) (https://ibb.co/B2jY9Dq)

(https://i.ibb.co/7GWw0Fn/15905373236924087555521914567314.jpg) (https://ibb.co/xMjprQ1)

(https://i.ibb.co/9WhgTHf/1590537368473214616152258323164.jpg) (https://ibb.co/4p2tTRD)

(https://i.ibb.co/YLCj06Z/15905375073502117306379045522648.jpg) (https://ibb.co/TgfhWZL)

(https://i.ibb.co/RHd7csV/15905375448111476484002766551511.jpg) (https://ibb.co/Thdrt7F)

(https://i.ibb.co/PGXPKCT/15905376167646872769358520432660.jpg) (https://ibb.co/b5wCTdH)

(https://i.ibb.co/tMBYRvF/15905377526507725942879199418591.jpg) (https://ibb.co/PZx1kP0)

(https://i.ibb.co/fDjm6sc/20200526-200939.jpg) (https://ibb.co/rdDn8VW)

(https://i.ibb.co/Khfb7Q0/15905397060086154713634646280802.jpg) (https://ibb.co/qjc794y)

(https://i.ibb.co/Q8G8hMv/15905397549771757104277677380420.jpg) (https://ibb.co/8zVzG9g)
Title: Re: SKS Cleaning Kit Use
Post by: Phosphorus32 on May 26, 2020, 09:42:49 PM
Nicely done Bruce  8) thumb1  I've never actually used an SKS cleaning kit  :)) but those are some handy tips on its use.
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on May 26, 2020, 09:53:22 PM
Yeah,that'a how I've always used mine.Thought eveyone knew.

When cleaning the M14/M1A we always used a 12ga shotgun hull for a bore guide at the muzzle when shoved over it after punching out the primer first.Works perfect and much less expensive than those fancy brass bore guides.
Title: Re: SKS Cleaning Kit Use
Post by: newchi on June 01, 2020, 09:38:33 PM
i used it once to see how it worked.  I think it solves the "how do we make sure these dip****s dont wreck the crown" problem, and it goes as far as it needs to, even though it seems short compared to what we are used to with commercial kits.
Title: Re: SKS Cleaning Kit Use
Post by: Larry D. on June 02, 2020, 12:36:20 PM
Quote from: Bubbazinetti on May 26, 2020, 09:53:22 PM
Yeah,that'a how I've always used mine.Thought eveyone knew.

When cleaning the M14/M1A we always used a 12ga shotgun hull for a bore guide at the muzzle when shoved over it after punching out the primer first.Works perfect and much less expensive than those fancy brass bore guides.

Honestly, I think most owners don't know how it works.
I've seen posts on several boards with people complaining that the rod is too short. Someone will usually chime in and tell them that it's a two man operation - you need two rods screwed together.... Not entirely sure how to screw two rods together since there's no way to do it.

I do appreciate the effort it took to put this tutorial together and post it up.

Maybe a sticky is in order? What does the boss mod think?
Title: Re: SKS Cleaning Kit Use
Post by: running-man on June 02, 2020, 12:51:22 PM
Yeah, I need to devote a good chunk of time to my to-do list for the board.  Been spending most of my time outside on honey-dos! 
Title: Re: SKS Cleaning Kit Use
Post by: Larry D. on June 02, 2020, 12:53:28 PM
Quote from: running-man on June 02, 2020, 12:51:22 PM
Yeah, I need to devote a good chunk of time to my to-do list for the board.  Been spending most of my time outside on honey-dos!

Outside honey-do's are way better than inside honey-do's. The worst possible honey-do is getting voluntold to do them for in-laws.
Title: Re: SKS Cleaning Kit Use
Post by: carls sks on June 02, 2020, 03:25:03 PM
appreciate the time to show this, thanks Bruce.  thumb1 remember seeing  a vid on u/tube showing this also, but forgot all about it. happens with getting old.  pullhair1
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on June 02, 2020, 04:18:23 PM
Another thing that contributes to the confusion of how the cleaning kit is deployed is how many AK kits are sold or represented as being for a SKS when in fact they're not the same.I see it a lot.
Title: Re: SKS Cleaning Kit Use
Post by: echo83 on June 02, 2020, 07:57:22 PM
Thanks for putting this together! I just got a 5 piece AK 47 kit delivered today from What A Country and the visuals here are super helpful. Mine has a punch, scraping tool, slave pin, brush and jag.

It's really well designed...but for an AK. (Not quite a perfect match for the SKS, but serviceable. )

Unfortunately, my cleaning rod won't screw into it, I think the threads are shot.

Does anyone know if the cleaning rods from Liberty Tree Collectors will work with my kit? Here's a link to the rod:

https://www.libertytreecollectors.com/productcart/pc/viewPrd.asp?idproduct=3323
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on June 02, 2020, 11:00:31 PM
I have no idea other than yes,they are the right length for a standard SKS 20" rifle.But here's the thing that I've found.Between my Type 56 Sporter carbine and my Type 56 rifle the rod tips WILL NOT interchange because the two kits although appearing the same have slightly different threads for the jag and bore brush.The rifle has M4-.8 or 8-32 threads and the carbine has slightly finer threads @ M4-.70 so the accessories will only work with their respective cleaning kits.That is what I have discovered.

You may be better off checking the threads on your rod,jag and brush to see if they're compatible.I'm sure you could likely chase the threads on your rod with the appropriate thread die to clean it up new again if you have access to such tools.It probably wouldn't take much.

I don't know if AK kits are different like that but I wouldn't be surprised at all if they were especially if they are Chinese.
Title: Re: SKS Cleaning Kit Use
Post by: Larry D. on June 03, 2020, 03:21:09 AM
Tickbite has some pretty nice rods for Yugos.

There must be some difference for them to specify it.
Title: Re: SKS Cleaning Kit Use
Post by: ffjoey on June 12, 2020, 09:59:29 AM
Nice little tutorial.
Title: Re: SKS Cleaning Kit Use
Post by: echo83 on June 20, 2020, 10:36:10 PM
Quote from: Bubbazinetti on June 02, 2020, 11:00:31 PM
I have no idea other than yes,they are the right length for a standard SKS 20" rifle.But here's the thing that I've found.Between my Type 56 Sporter carbine and my Type 56 rifle the rod tips WILL NOT interchange because the two kits although appearing the same have slightly different threads for the jag and bore brush.The rifle has M4-.75 threads and the carbine has slightly finer threads @ M4-.70 so the accessories will only work with their respective cleaning kits.That is what I have discovered.

You may be better off checking the threads on your rod,jag and brush to see if they're compatible.I'm sure you could likely chase the threads on your rod with the appropriate thread die to clean it up new again if you have access to such tools.It probably wouldn't take much.

I don't know if AK kits are different like that but I wouldn't be surprised at all if they were especially if they are Chinese.

Thanks for the info. I just got a cleaning rod from Sarco today. The threads fit my cleaning kit perfectly, which is a relief, but the rod is a little shorter than my SKS rod.

Also, I had to shave off a little off the knob to get it to fit right in in the lug that holds the cleaning rod in. Sigh.

Oh well. I use an Amazon rifle kit for cleaning anyway, and a bore snake, too. Right now, I have a Chinese metal two-compartment oiler and a bore snake in my Chinese chest rig. The AK cleaning kit/egg and the too-short rod will work in a pinch.

I think I'm done with chasing around oilers and cleaning kits for now...time to track down the impossible to find blade bayonet and leave well enough alone!
Title: Re: SKS Cleaning Kit Use
Post by: echo83 on June 30, 2020, 10:39:49 PM
After a few days, my OCD set in...while the rod fits the threads on all the tools in my cleaning kit, I decided that it fits only because the rod is for an AK, and so is the cleaning kit.

I called Sarco yesterday, and let them know that I'm pretty sure they sent me an AK rod, since it's a good 2 inches shorter than my SKS rod. They said they'd send me an SKS rod free of charge, which is really cool of them. Hopefully they follow through.

I'm beginning to see why the insurgents just knotted a shoelace and dipped it in motor oil.

In a perfect world, the replacement rod they send will fit my cleaning attachments. The lengths I'm going to just to put together a rod and cleaning kit that I'll probably never use are a little embarrassing.

Now I just need to track down an empty egg to keep all the tool parts in, because they're all in great shape.
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on June 30, 2020, 11:58:54 PM
If it is a rifle you need a standard 17" SKS rod.
Title: Re: SKS Cleaning Kit Use
Post by: Justin Hell on July 01, 2020, 05:51:38 PM
I am not positive on this, but the likely reason that folks are having a hard time with their cleaning rods fitting AK kits, is due to the AK continuing production, and they likely moved onto a modern threading system, that the SKS didn't live long enough to see.

SKS cleaning rods are threaded using the Whitworth system.  The more modern AK kits are likely for AKMs which I am guessing moved onto a more modern type some time ago.  The Chinese likely carried on the tradition and overproduced kits and rods while they carried on with SKS production far longer than anyone else. Enough that you can still find them pretty easily.  Being a disposable component, they likely, at least for awhile made more kits than guns. Rods, maybe to a lesser degree...but loss must have been considered for a 'loose' part. 

I am just speculating here though...the closest thing I have to an AK is a SKS Sporter, which oddly has a cleaning rod, but no kit.  pullhair1
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on July 01, 2020, 07:41:07 PM
What do you mean? My Type 56 thumbhole Sporter came with a cleaning kit and decarboning tool taped together in the box.The rod end and tips don't match up to my older Navy commercial though.The rod is about 13-1/8" o.a.l.,threads are confirmed M4-.7 for my Sporter rod.My rifle has 8-32 threads and definitely not Whitworth(too large) from my measurements and references.
Title: Re: SKS Cleaning Kit Use
Post by: Justin Hell on July 02, 2020, 12:11:59 PM
Quote from: Bubbazinetti on July 01, 2020, 07:41:07 PM
What do you mean? My Type 56 thumbhole Sporter came with a cleaning kit and decarboning tool taped together in the box.The rod end and tips don't match up to my older Navy commercial though.The rod is about 13-1/8" o.a.l.,threads are confirmed M4-.7 for my Sporter rod.My rifle has 8-32 threads and definitely not Whitworth(too large) from my measurements and references.

Ha! I was unaware that Sporters actually came with kits....I didn't get mine new. I also have never attempted to use the rod for it.  Actually, when I last looked into the threading...I was working on my Sporter.  What I was contemplating doing was modding a bubba stock to have a retaining nut for the rod similar to a Mosin.  This was to retain a Choate muzzle brake using a rod instead of the ugly nut and bolt that used the cleaning rod hole in the FSB.  I discovered somewhere, that the nut I was seeking required Whitworth threads....which you just don't find at your local Ace.    Reading through this thread dusted off that little factoid I had been holding onto.  Ultimately I took a crummy NC Star rod, and rethreaded it for a common nut.

This is when I learned how crappy NC Star rods are.  When tightening down the nut...it simply pulled the pressed on, not milled head right off of the dang rod.   That is when this idea died on the vine, I wasn't going to bugger up a real cleaning rod.

This makes me want to check all my rods and their respective kits, many obtained to complete SKSs whose previous owners 'lost' them.  Lord knows what kind of threading mismatches I have going on.  It also reminds me I am three rods short, two NC Stars that are 'just for looks' and one for a bubba whose rod was spirited away for a build I did later.  I like to keep my bubba's original stuff on hand for the ability to return to normal.  What sucks is my preferred source for them is Canadian...and the other day I watched as all of his stuff was pulled off eBay, item by item.  The only other place I know that has them I kinda don't like dealing with.  banghead1

All this said, I betcha the SKS I have inbound from Classic is one of the few that won't have one.  nailbite1
At least I have a tobacco can full of Albanian/Chinese kits from the 2012 imports....that are in perfect condition to go back into these new imports.
Title: Re: SKS Cleaning Kit Use
Post by: Larry D. on July 02, 2020, 03:44:35 PM
Is this the Whitworth stuff we're talking about: https://www.amazon.com/Whitworth-British-Standard-BERGEN-AT045/dp/B01MQ2M3C9

It's not a ton of money.

I'm thinking that an adapter could be made for the purists among us.

I don't use the SKS kits as I have LOTS of other options available, but a Whitworth/SAE/Metric/Whatever to whichever thread adapter might be a hobby project.
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on July 02, 2020, 04:26:02 PM
Of the 5 AKM and Type 56 rifles and Sporters that I have observed none had BSW(British Standard Whitworth) threads.Even the closest one,the 3/16-24,is too large and coarse.My Maadi RML and Type 56 rifle original issue cleaning rods are threaded 8-32.My Sporter rod is M4-.7 threads.The rod tips do not interchange.
Title: Re: SKS Cleaning Kit Use
Post by: Justin Hell on July 02, 2020, 08:16:54 PM
Quote from: Larry D. on July 02, 2020, 03:44:35 PM
Is this the Whitworth stuff we're talking about: https://www.amazon.com/Whitworth-British-Standard-BERGEN-AT045/dp/B01MQ2M3C9

It's not a ton of money.

I'm thinking that an adapter could be made for the purists among us.

I don't use the SKS kits as I have LOTS of other options available, but a Whitworth/SAE/Metric/Whatever to whichever thread adapter might be a hobby project.

I do recall it being a British standard, primarily used for camera tripods and some older stage lighting clamps, from what I have read.  It's a heckuva lot of ching for me to throw at, considering how many times I haven't used either my metric set, or my dad's SAE set. I forgot I borrowed that actually. :P
Title: Re: SKS Cleaning Kit Use
Post by: newchi on July 03, 2020, 02:39:03 PM
The only 2 British threads i remember (being born there) are British Standard Pipe Thread. Back when you would cut steel pipe and thread the ends and join them.
And possibly more relevant to this, there is such a thing as British gun cleaning kit thread.  Thats NOT what it is called but my nice Shotgun kit wont work with anything in north america.

I think, if you live near a decent sporting goods store a Parker Hale adaptor might be something to try.
https://www.amazon.com/Dewey-Rods-Small-Parker-Adapter/dp/B01CW3HE7E

And on this page theres something called a military thread adaptor that ive never heard of.
https://www.amazon.com/Pro-Shot-Thread-Standard-Military-Adaptor/dp/B008P8F4ZA/ref=pd_sbs_200_4/141-0652703-9826923?_encoding=UTF8&pd_rd_i=B008P8F4ZA&pd_rd_r=d5e12f9d-c941-4a79-82ac-479cd09eb420&pd_rd_w=VCpc3&pd_rd_wg=mQ1vo&pf_rd_p=d28ef93e-22cf-4527-b60a-90c984b5663d&pf_rd_r=NSDHRJS94N4KQGTVZE7G&psc=1&refRID=NSDHRJS94N4KQGTVZE7G
Title: Re: SKS Cleaning Kit Use
Post by: carls sks on July 03, 2020, 03:00:54 PM
i'm just so darn lazy  pullhair1, i ordered a bore snake to clean. i even had to look up size needed (.30 cal for others), got to get out more.  banghead1
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on July 03, 2020, 03:24:24 PM
You know that the BSW and BSF thread standards were replaced by the UNC standard since the 1950s? The differences in thread pitch is identical with very few exceptions.The main difference is the "V" angle of the Whitworth is 55 degrees and the "V" angle of the UNC threads is 60 degrees. For most practical purposes a UNC 8-32 bolt will screw into a BSW 8-32 female thread and vice versa.You can run a UNC thread die over to make life easier if need be and you'll hardly see any material be taken off if any from my experience.No need for an adapter that I can see.
Title: Re: SKS Cleaning Kit Use
Post by: newchi on July 03, 2020, 04:44:01 PM
I dont remember why they dont fit , just they are different some how.
I wish there was a thread app where you took a photo and it told you what it was
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on July 03, 2020, 05:54:00 PM
Sometimes the pitches are different but for the most part a BSW 5/32-32 (.156" major diameter) is only a few thousands difference from a UNC 8-32(.164" major).This size is also very close to a metric M4-.7(.157" major diameter) but the pitch is .004" different so they won't interchange.Looks to me that there is two standard rods.You'll have one or the other.Only measuring the dia. and pitch will reveal what you have.
Title: Re: SKS Cleaning Kit Use
Post by: Shoot The Refurbs on July 04, 2020, 05:08:17 AM
Quote from: Bubbazinetti on July 03, 2020, 05:54:00 PM
Sometimes the pitches are different but for the most part a BSW 5/32-32 (.156" major diameter) is only a few thousands difference from a UNC 8-32(.164" major).This size is also very close to a metric M4-.7(.157" major diameter) but the pitch is .004" different so they won't interchange.Looks to me that there is two standard rods.You'll have one or the other.Only measuring the dia. and pitch will reveal what you have.
I had no clue there were any differences between them much less the exact differences drawn out to the .000
but I am just stunned you happened to know this and have the exact specifications onhand. extremely impressive sir. clap1
Title: Re: SKS Cleaning Kit Use
Post by: Larry D. on July 04, 2020, 02:59:35 PM
Quote from: Bubbazinetti on July 03, 2020, 05:54:00 PM
Sometimes the pitches are different but for the most part a BSW 5/32-32 (.156" major diameter) is only a few thousands difference from a UNC 8-32(.164" major).This size is also very close to a metric M4-.7(.157" major diameter) but the pitch is .004" different so they won't interchange.Looks to me that there is two standard rods.You'll have one or the other.Only measuring the dia. and pitch will reveal what you have.

Sounds like you've been around a shop or two.
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on July 04, 2020, 05:47:55 PM
Was a fabricator for aerospace industry and mechanic for a long time.There's a hell of a lot that I don't know still.Always fun to learn.
Title: Re: SKS Cleaning Kit Use
Post by: Shoot The Refurbs on July 04, 2020, 06:59:18 PM
Quote from: Bubbazinetti on July 04, 2020, 05:47:55 PM
Was a fabricator for aerospace industry and mechanic for a long time.There's a hell of a lot that I don't know still.Always fun to learn.
A skillet! I should have known, some of the handiest people I've ever met.
Title: Re: SKS Cleaning Kit Use
Post by: echo83 on July 08, 2020, 07:57:36 PM
So the replacement rod came in yesterday. My heart sank, because the box it shipped in was the exact same size as the box the AK rod came in...

Then I noticed an inch of cleaning rod jutting out through the side of the box!

The rod is in great (unissued?) shape, the length matches the one my rifle came with 64 years ago...perfectly blued and with a healthy coating of cosmoline. Best of all, the threads all fit perfectly with my AK cleaning kit. Success! And big tip of the hat to Sarco for replacing the rod free of charge!

I also noticed that the threads matched the mashed up and flattened threads on my original rod.

Conclusion: SKS cleaning rod threads are compatible with AK cleaning kit parts.

I feel like I'm pushing my luck, but does anyone know where I can track down an empty SKS cleaning kit egg to house all the cleaning kit parts?
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on July 08, 2020, 09:26:04 PM
J&G has them for short money right now.
https://www.jgsales.com/military-surplus-sks-and-ak-cleaning-kit-for-buttstock,-used.-p-70045.html (https://www.jgsales.com/military-surplus-sks-and-ak-cleaning-kit-for-buttstock,-used.-p-70045.html)

Title: Re: SKS Cleaning Kit Use
Post by: Shoot The Refurbs on July 09, 2020, 12:30:00 AM
thanks for the link bubba, just snagged 10, I'm always short on those and the rifles I do buy often don't have them. while there I noticed they had a few russian refurb sks's in stock.... They want about a grand each though.
https://www.jgsales.com/russian-sks-semi-auto-rifle,-7.62x39,-black,-russian-arsenal-rebuild-with-laminated-stock,-c-r,-vg,-used.-p-105063.html

***EDIT***
Just noticed they have chinese too.... for just over 600$ each...
https://www.jgsales.com/norinco-sks-semi-auto-rifle,-7.62x39,-factory-26-manufacture,-blued,-spike-bayonet,-vg+,-used-p-105051.html
Title: Re: SKS Cleaning Kit Use
Post by: carls sks on July 09, 2020, 11:30:36 AM
Quote from: Bubbazinetti on July 08, 2020, 09:26:04 PM
J&G has them for short money right now.
https://www.jgsales.com/military-surplus-sks-and-ak-cleaning-kit-for-buttstock,-used.-p-70045.html (https://www.jgsales.com/military-surplus-sks-and-ak-cleaning-kit-for-buttstock,-used.-p-70045.html)

very tempting ($12 shipping for 10), thanks.
Title: Re: SKS Cleaning Kit Use
Post by: Bubbazinetti on July 09, 2020, 11:38:48 AM
Yeah,that last Jianshe with all matching and the beautiful Russian refurb are in really nice shape.Much better than many of the tired gunsmith specials on the market.A better value I think as compared to the gunjoker insanity going on right now.I hope you can snag one.
Title: Re: SKS Cleaning Kit Use
Post by: Shoot The Refurbs on July 09, 2020, 02:11:23 PM
Quote from: carls sks on July 09, 2020, 11:30:36 AM
Quote from: Bubbazinetti on July 08, 2020, 09:26:04 PM
J&G has them for short money right now.
https://www.jgsales.com/military-surplus-sks-and-ak-cleaning-kit-for-buttstock,-used.-p-70045.html (https://www.jgsales.com/military-surplus-sks-and-ak-cleaning-kit-for-buttstock,-used.-p-70045.html)

very tempting ($12 shipping for 10), thanks.
Had to, was only 10$ shipping to Texas, weird.

Quote from: Bubbazinetti on July 09, 2020, 11:38:48 AM
Yeah,that last Jianshe with all matching and the beautiful Russian refurb are in really nice shape.Much better than many of the tired gunsmith specials on the market.A better value I think as compared to the gunjoker insanity going on right now.I hope you can snag one.
Oh no definitely not I. I still don't see a grand being value on a normal russian refurb, and absolutely not over 600 for a chinese.
Deals still can be had even on Gunjoker. Sometimes you have to be really fast though, I just picked up something neat that I'll post pics of when I get, but when I slammed the BIN I was the only person to have viewed it. Possibly due to a spelling error, (no more hints though, Y'all just have to wait and see  dance2 )
(https://i.ibb.co/GnXKhWN/fast-grab.png) (https://imgbb.com/)
I'm more than willing to pay price for a gun, but man, a grand for a nothing special bbq refurb? That's just panic pricing on J&G's part, but I guess they can only sell me the cleaning kits so cheap if they gouge one or 2 people on an SKS.  rofl



Title: Re: SKS Cleaning Kit Use
Post by: Larry D. on July 10, 2020, 02:06:46 PM
J&G is an interesting place.
It's easy to miss their driveway. They sit back a ways kinda behind a post office, a feed store, and some other business.
But once to find it, there's some deals to be had on occasion.
The hired help has changed a lot over the years. They're not as helpful, or friendly, as they used to be.
I usually make a run up there once a year or so. Prescott (pronounced PRESS-kit by us desert dwellers) is a nice town. It's famous in these parts for Whiskey Row. Google that term.
For us old guys, do y'all remember the movie Billy Jack? That famous scene about "I'm gonna take this right foot, and I'm gonna whop you on that side of your face..." was filmed at the courthouse in downtown Prescott. For the younger folks: https://www.youtube.com/watch?v=LLN8-buqDIs
Anyway, back to J&G. Once you get in there, you're a little surprised at how small the public area/showroom is compared to the size of the building. They have a pretty good sized warehouse area, and they keep a LOT of stuff back there.
You just never know what's gonna pop up.
True story: Me and my buddy Frank took a vacation day at work and made the trip up there to get out of the heat, visit J&G, and have lunch. Frank wanted a shotgun they had on sale, but I had no plans to buy anything at all. While Frank was doing paperwork, I was leaning on a counter. This old fella comes out of the back and asks me if I need any help.  said no thanks. It was slow, so we started chatting. While yakking, I noticed a nifty little 2 tone pistol that looked like a PPK.
That's how I bought my first PA-63.
Frank comes back and I tell him I'm getting ready to do my paperwork.
About this time, a dude comes out of the back with a laundry cart about half full of used pistols that have just cleared and are ready for sale.
Me, Frank, and another customer sorta amble over to that counter. The 3 of us and 3 employees start the process of handing each pistol to each other in a circle.
One of the guns that came out was a Smith & Wesson Model 52. Never saw one before. Never seen one since. Very interesting gun. Anyway, I wound up with that PA-63, a stainless Ruger MKII, and a Smith Model 10. Frank took 3 guns home as well. That third customer took the Smith Model 52.
Another time I was fingering some AK's that had just come in. I noticed something odd about it, so I called one of the guys over to see. There was this strange extra hole in the receiver.... Maybe I shoulda kept my mouth shut and bought it, but I did the correct thing. Maybe the employee bought it, but e both knew that somebody screwed up and slipped a 3 hole receiver in that shipment.

They frequently have boxes of random milsurp accessories laying around. I scored 3ea WWII vintage German K98 ammo pouches for 3 bucks apiece one time. Random sales on all sorts of guns that aren't listed on the website.

But the strangest thing about them - they want ID on every sale. Even a non firearm sale. Some guys get offended and won't do it. Every sale gets you on their mailing list, too.